An adaptive sliding mode observer based near-optimal OER tracking control approach for PEMFC under dynamic operation condition

Tracking control of oxygen excess ratio (OER) is crucial for dynamic performance and operating efficiency of the proton exchange membrane fuel cell (PEMFC). OER tracking errors and overshoots under dynamic load limit the PEMFC output power performance, and also could lead oxygen starvation which seriously affect the life of PEMFC. To solve this problem, an adaptive sliding mode observer based near-optimal OER tracking control approach is proposed in this paper. According to real time load demand, a dynamic OER optimization strategy is designed to obtain an optimal OER. A nonlinear system model based near-optimal controller is designed to minimize the OER tracking error under variable operation condition of PEMFC. An adaptive sliding mode observer is utilized to estimate the uncertain parameters of the PEMFC air supply system and update parameters in near-optimal controller. The proposed control approach is implemented in OER tracking experiments based on air supply system of a 5 kW PEMFC test platform. The experiment results are analyzed and demonstrate the efficacy of the proposed control approach under load changes, external disturbances and parameter uncertainties of PEFMC system.     

多维不确定性影响下的水期权交易最优策略研究

为解决来水预测不确定性和水价不确定性给用水户带来的风险对冲问题,引入对冲性的水期权交易模式,建立了以用水户期望收益最大为目标的水期权交易模型,得到了最优的期权交易策略应满足的条件,并利用二分法计算得到了最优的期权交易策略,探究了来水不确定性与水价不确定性对期权交易策略的影响。结果表明,来水预测误差和水价的波动越大,用水户的期望收益越大,最优的期权交易策略能有效降低来水预测不确定性和水价不确定性带来的风险。     

Systematic packaging design tools integrating functional and environmental consequences on product life cycle: Case studies on laundry detergent and milk

This study presents systematic packaging design tools integrating functional and environmental consequences on product life cycle. To design packaging for sustainability, the trade-offs between functional and environmental aspects of packaging throughout the product life cycle should be considered. However, it is difficult for packaging designers to understand the overall trade-offs because the extent of the design consequences on the entire life cycle of packaging and its contents is unclear. We developed two tools for packaging design: the Life Cycle Association Matrix (LCAM) and the Function Network Diagram (FND). The following three steps, based on literature reviews and interviews with industrial experts, were applied. Firstly, we listed the product functions and design variables related to the functions as the attributes allocated to the product life cycle. Secondly, the attributes were connected appropriately based on causal relationships. Lastly, we identified the factors to support decision making in the packaging design procedure. As a result, the LCAM depicts the design consequences on the life cycle, and the FND determines the stakeholders affected by the design consequences. Two case studies were demonstrated to analyze the trade-offs by using our tools. In the case studies, a liquid laundry detergent bottle and a milk carton were redesigned. The tools identified the design consequences and stakeholders affected by the redesign of the usability and protective function for the detergent and milk cases, respectively. The results showed the significance of understanding the design consequences on the product life cycle by integrating the functional and environmental aspects.     

某型运输机飞行状态下冷凝器风道性能

以某型运输机蒸发循环制冷系统用冷凝器为研究对象，分析了运输机与直升机、小型通航飞机蒸发循环制冷系统工作环境的区别，应用Star CCM+软件进行了仿真建模，通过对冷凝器风道的流体仿真分析，阐述了飞行状态下引起蒸发循环制冷系统压力故障的原因，在此基础上提出了冷凝器风道优化方案，并应用流体仿真分析的方法，验证了优化方案的有效性，最后在该运输机上进行了试飞验证。     

LD27-2油田稠油油藏蒸汽吞吐中后期注采参数优化研究

蒸汽吞吐是稠油油藏开发的最有效措施之一，但是对于海上油田的特殊条件，在进行蒸汽吞吐3~4轮后，即意味着进入蒸汽吞吐中后期。此时，如何调整注采参数，是海上稠油油藏高效开发的关键。针对LD27-2油田稠油油藏的开发特点，在地质建模和高度历史拟合的情况下，对LD27-2油田稠油油藏开发状况进行多轮次预测；基于生产历史拟合的油藏数值模型，开展了不同蒸汽干度、注汽强度、注汽强度递增等条件下A22H井和A23H井蒸汽吞吐至开采至10年的油藏数值模拟，明确不同注采参数的影响规律，优化了LD27-2油田稠油油藏蒸汽吞吐中后期注采参数。     

Effect of nano-sized Al2O3 reinforcing particles on uniaxial and high cycle fatigue behaviors of hot-forged AZ31B magnesium alloy

The effect of hot-forging process was investigated on microstructural and mechanical properties of AZ31B alloy and AZ31B/1.5vol.%Al₂O₃ nanocomposite under static and cycling loading. The as-cast alloy and composite were firstly subjected to a homogenization heat treatment at 450 °C and then an open-die forging at 450 °C. The results indicated that the presence of reinforcing particles led to grain refinement and improvement of dynamic recrystallization. The forging process was more effective to eliminate the porosity in the cast alloy workpiece. Microhardness of the forged composite was increased by up to 80% and 16%, in comparison with those of the cast and forged alloy samples, respectively. Ultimate tensile strength and maximum tensile strain of the composite were improved by up to 45% and 23%, compared with those of the forged alloy in similar regions. These enhancements were respectively 50% and 37% in the compression test. The composite exhibited a fatigue life improvement in the region with low applied strain; however, a degradation was observed in the high applied strain region. Unlike AZ31B samples, tensile, compressive and high cycle fatigue behaviors of the composite showed less sensitivity to the applied strain, which can be attributed to the amount of porosity in the samples before and after the hot-forging.     

盐冻融与干湿作用下沥青混凝土的高低温力学性能分析

制备了沥青混凝土样品,并进行了不同次数的盐冻融干湿循环试验。在此基础上,测试了沥青混凝土的高温车辙深度、动稳定度和低温抗弯拉强度,得到了车辙深度、动稳定度和抗弯拉强度随盐冻融干湿循环次和盐浓度的变化规律,研究了盐冻融与干湿作用下沥青混凝土的高低温力学性能。研究结果表明:(1)沥青混凝土60min车辙深度随盐浓度的增加和冻融循环次数的增多而呈线性增长的趋势;(2)沥青混凝土的抗高温变形能力随盐冻融干湿循环次数的增多而逐渐弱化;(3)沥青混凝土的抗弯拉强度经历9次和15次盐冻融干湿循环后分别下降22%~26.4%和42.6%~51.5%;(4)冻融干湿循环次数一定时,沥青混凝土的抗弯拉强度随盐浓度的增加而缓慢下降,并且当盐浓度达到12%时,沥青混凝土的抗弯拉强度减小就很不明显。     

Investigating azeotropic separation of hydrochloric acid for optimizing the copper-chlorine thermochemical cycle

In this paper, an atmospheric-pressure distillation system is designed and constructed for partial to separation of hydrochloric acid and water. The system concentrates HCl(aq) between the electrolyzer and hydrolysis processes of the Copper–Chlorine (Cu–Cl) cycle for hydrogen production. The motivation behind this study is to investigate azeotropic separation of HCl(aq), as needed for integration of unit operations in the Cu–Cl cycle. The separation is only partial, as the mixture is unable to cross the azeotrope with only a single pressure. The distillation system consists primarily of one packed distillation column, which employs heating tapes and thermocouples to achieve a desired axial temperature profile. The column can be operated in batch or continuous mode. The distillate is H 2O(l) and the bottoms is HCl(aq) near the azeotropic concentration; feed concentrations are less than azeotrope. Thus, the degree of separation is determined to be independent of the feed concentration. The bottoms concentration varies from experiment to experiment, but does so independently of feed concentration, likely the result of corrosion impurities affecting the calculation of its concentration. It is found that HCl(aq) can be concentrated up to approximately 0.1068 mol/mol from an initial concentration of 0.0191 mol/mol. A simulation of pressure-swing distillation (PSD) is also performed, but due to safety constraints (a column operating at 10 atm must be certified to CSA B51), a single-pressure (single-column) distillation is physically performed. A single-pressure column is beneficial to the Cu–Cl cycle because it partially recycles HCl, which reduces the cost of the cycle, and still provides valuable results for analysis. The maximum HCl concentration achieved experimentally is 0.1068 mol/mol and the maximum HCl concentration determined from simulation is 0.11 mol/mol (the azeotropic concentration). The novelty of this research is that the experimental column built to study HCl partial separation is designed to be simple yet safe to integrate within the Cu–Cl cycle for hydrogen production.     

Effects of electrical parameters and their interactions on plasma electrolytic oxidation coatings on aluminum substrates

Based on orthogonal experiments, the effects of voltage, frequency, duty ratio and their interactions on the thickness and corrosion resistance of coatings prepared by plasma electrolytic oxidation (PEO) on aluminum in an alkaline silicate-containing electrolyte were investigated. The thicknesses of these coatings were obtained by measuring their cross-section using Image J software. Their corrosion resistances were evaluated in HCl and NaCl media through spot test and electrochemical test. The results show that the experimental design of this study is the key to investigate the interactions among these electrical parameters. Additionally, not only each independent factor, but also their interactions exhibit a remarkable influence on the coatings. The combination of high voltage, low frequency and large duty ratio significantly increases the coating thickness and content of the corrosion resistance phase, and thus improves the corrosion resistance of the coating in HNO₃ medium. Conversely, the coating possessing the densest microstructure and best corrosion resistance in NaCl medium is obtained when low voltage and high frequency match with a small duty ratio.